![ntopaz-image-0](https://artisteem.io/media/6f2bdd06-d7f9-464a-bea3-d10035f2beb2)![ntopaz-image-1](https://artisteem.io/media/7ec73c1f-4890-4a26-87ad-f2051a33b686)![ntopaz-image-2](https://artisteem.io/media/31f4ef70-e61f-4dd9-b51c-99d716bc6c35)![ntopaz-image-3](https://artisteem.io/media/fd2a9559-9363-44c3-8f86-4abfd54c4a26)![ntopaz-image-4](https://artisteem.io/media/d71116f4-d32a-465a-b814-d347a678fcb3)![ntopaz-image-5](https://artisteem.io/media/6843f22e-1a55-4394-ace7-ae6c32ed6e70)This is an candy dispenser made from waste materials.

Tools and materials are:
1, hot melt glue gun
2. Ruler, pencil, scissors, carving knife: used for drawing and cutting
3. Mineral water bottles
4. Used cartons

Production process:
1. Cut the used water bottle with scissors from the bottom, leaving the length about 12cm, then cut the top part from the outside of the bottle, do not cut, like a container with a lid, from which the candy can go
2, calculate the size, first draw on the cardboard, and then according to the pattern of the drawing with a carving knife cut out the cardboard box two circles, leaving the rest of the part, and then cut out four, because the cardboard is still thin, stick the two flat, so that there are only two flat, two circular border. The circular frame is used as the base to hold the container, and the pincket is used to block the base.
3. Use the hot glue gun to glue the water bottle cut out from the previous to the cardboard, so that the model of the candy machine is finished.

This is just the initial model of the candy machine, and there's a lot of need to improvement, the next plan is:
1. Increase the number of containers to 3 to 5. Use thin and long ones instead of short and thick ones
2, the switch USES the button mode, one candy go out while pressing a button once, that’s more convenient than the hand pull mode
3. Beautify the appearance

这是利用废旧物品作的一个糖果机原型。
工具和材料有：
1、	热熔胶枪
2、	直尺，铅笔，剪刀，刻刀：用于画图纸和裁剪
3、	矿泉水瓶
4、	废旧纸箱

制作过程：
1、	把用过的矿泉水瓶从底部用剪刀剪开，保留长度大概12厘米左右，再把上面部分从瓶子外沿剪开，不要剪断，像是一个带盖子的容器，糖果可以从这里面放进去
2、	算好尺寸，先在纸板上画出来，然后按照图纸样式用刻刀把纸盒子剪出两个圆型，留下剩下的部分，再剪出四个平托，因为纸板还比较薄，把两个平托粘在一起，这样就只有两个平托，两个圆型边框。圆型边框是用来作为盛放容器的底座，平托是用来挡住底座，以后一拉平托就会掉出一个糖果。
3、	使用热熔胶枪把之前剪出来的矿泉水瓶和纸板粘在一起，这样糖果机的模型就做完了。

这只是糖果机的初始模型，还有很多地方可以再完善，下一步改进计划：
1、	增加容器到3至5个，使用细长型代替短粗型
2、	开关使用按钮方式，按一下出一个糖果，比手拉方式更便捷
3、	对外观进行美化修饰